First, Aerodynamic High Temperature Globe Valve Product Description
Valve heat sink is mainly used to protect the drive device, so the use of more on the control valve, in general, more than 300 ℃ heat sink, 200 ℃ through the bracket cooling, the drive will not have a significant impact. High temperature valve bonnet to add heat sink is to heat, which is no doubt that the temperature limit of the heat sink without the provisions of the standard, generally in the case of more than 560 ℃ heat sink.

And the best effect of the heat sink is welded with the valve cover, welding can also be, but the effect is not good casting. Pneumatic shut-off valve is simple in structure, easy to manufacture and maintain. The working stroke is small and the opening and closing time is short. The closing body (valve flap) and the sealing surface of the valve seat are tapered, the closing force is small, the erosion resistance and the sealing are reliable. Pneumatic shut-off valve seat can be replaced valve seat, can be any combination with the closure of the sealing surface material matching to meet the working conditions, to extend the service life.

 

Second, Aerodynamic High Temperature Globe Valve Pneumatic Actuator Configuration Features
 1, Compact dual piston gear rack structure, ratcheting precise, smooth transmission output torque stability. 
 2, The cylinder for the extrusion of aluminum alloy, and by the hard anodized, the surface texture of hard, strong wear resistance. 
 3, The same specifications are double acting and single acting (spring reset). 
 4, The piston and the output shaft of the active parts are installed wear-resistant material support, to avoid direct contact between the metal parts to reduce friction and wear. 
 5, Installation, connection size according to the international standard ISO5211.DIN3337 and VDI / VDE3845 design, with the ordinary pneumatic actuator interchangeable. 
 6, The cylinder, the end cap. Output shaft, spring, fasteners, etc. are anti-corrosion treatment. 
 7, The installation of the output shaft connection hole has a variety of shapes (square hole. Flat hole. Shaft hole) to choose from. 
 8, There are room temperature type. High temperature type, low temperature type. 
 9, Single-acting spring pre-compressed after the installation, easy to install, disassemble, and good security. 
 10, Beautiful appearance, light weight. Has a waterproof performance.

 

Third, The Function And Use Of Pneumatic Actuator Accessories
 Dual use as pneumatic Actuator: control valve opening or closing. 
 Single acting Pneumatic Actuator: Circuit. When the air is cut or faulty, the valve is automatically closed. 
 Single solenoid valve: valve when the power supply is turned on or off, when the valve off or open. 
 Double solenoid valve: a valve when the valve is turned on. When the other coil is energized, the valve is closed and the memory function is 
 Recirculated: the remote return valve opens or closes the signal. 
 Electrical positioner: According to the size of the current signal (4-20mA) on the valve to open (that is, the media flow) to adjust the control. 
 Electrical converter: the current signal into air pressure signal, and pneumatic positioning supporting the use of. 
 Pneumatic positioner: According to the pneumatic signal (0.02-0.1Mpa) size to control the valve opening, the adjustment control. 
 Pneumatic triple parts: pressure reducing valve. Filter. Oil mist, the gas source stability, cleaning and moving parts from the lubrication effect. 
 Manual mechanism: When the circuit is shut off or faulty, it is used to operate the valve opening and closing

 

 Fourth, Aerodynamic High Temperature Globe Valve Installation, Commissioning And Maintenance
 1, KGT series of pneumatic actuators can be directly connected with the valve, but also through the bracket and connector installed with the valve connection. 
 2, The installation must ensure that the pneumatic actuator output shaft and the valve shaft coaxial. 
 3, Pipe joints and ducts should be clean inside, no waste. Dust and oil and so on. 
 4, Solenoid valve. Electrical locator, electrical converter, pneumatic positioner. Reversal, etc. should be installed according to the relevant instructions. 
 5, Pneumatic actuators at both ends of the adjustment screw, you can adjust the valve opening angle, adjust the nut must be tightened after adjustment. 
 6, The actuator and the valve should be commissioned at the same time, the valve pressure to the rated pressure, the actuator to the gas source pressure 0.4-0.7Mpa on the two inlet switch inlet, observe the valve open and closed, should be flexible and no pause , And repeated trial and error. 
 7, The installation of the solenoid valve pneumatic actuator, commissioning should first use the manual button operation (solenoid button on the red button) debugging, and then power debugging. 
 8, The air supply should be kept dry. Clean, regularly with the actuator in conjunction with the air filter to discharge. Under normal use should be checked once a month, once a year.

 

 Fifth, Pneumatic High Temperature Cut Valve Implementation Of The Standard

Design and Manufacture		GB / T1223
Connection Size	Structure Length	GB / T12221
	Flange Size	JB / T79
Inspection and Testing		JB / T9092
Material	Carbon Steel	GB / T12229
	Stainless Steel	GB / T12230
	Alloy Steel	Q / ZB6
Logo		GB / T12220
Supply		JB / T7928

 

Six, Aerodynamic High Temperature Globe Valve Structural Characteristics
 1, Selection of sophisticated, in line with domestic and foreign standards, reasonable structure, handsome in appearance. 
 2, The valve, the valve seat sealing surface with iron-based alloy surfacing or Stellite (Stellite) cobalt-based hard alloy surfacing, wear, high temperature, corrosion resistance, scratch resistance, long service life The 
 4, Stem and quenched and tempered surface treatment, a good corrosion resistance and scratch resistance. 
 5, Can be used in a variety of piping flange and flange sealing surface type to meet the needs of various projects and user requirements. 
 6, The full range of valve material, packing, gasket can be based on actual conditions or user requirements reasonable matching, can be applied to a variety of pressure, temperature and media conditions. 
 7, Inverted seal with a threaded connection Seal or body welded austenitic stainless steel, sealed and reliable, replace the filler can be carried out in the case of non-stop, convenient and quick, does not affect the system operation.

 

Seven, Aerodynamic High Temperature Globe Valve Main Parts Materials

Body	Cap	Discs	Sealing Ring	Stem	Filler	Applicable Media	Applicable Temperature (≤ ℃)
WCB		WCB + D507MO	D577	2Crl3	Flexible Graphite	Water, Oil, Steam	425
ZGlCrl8Ni9Ti		0Crl8Ni9Ti  Stellite12	Stellite6	lCrl8Ni9Ti	PTFE	Nitric Acid	200
ZGlCrl8Ni2Mo2Ti		CF8M  Stellite12	lCrl8Ni2Mo2Ti	lCrl8Ni2Mo2Ti	PTFE	Phosphoric Acid,  Alkali, Mixed Acid	200
ZG00Crl7Nil4M02	CF3M  Stellite12	Stel1ite6	316L	PTFE	Phosphoric Acid,  Urea, Methyl Ammonium Liquid	200
ZGlCr5MO	ZGlCr5MO  Stellite12	Stel1ite6	25Cr2Mo1VA	Flexible graphite	Water, oil, steam	550

Eight, Aerodynamic High Temperature Globe Valve Main Dimensions, Connection Size

Nominal Pressure PN (MPa)	Nominal Diameter DN (mm)	Standard Value										Reference
		L	D	D1	n2	D6	b	f	f1	Z-φd	L1	H
1.6	50	230	160	125	100		16			4-φ18	185	645
	65	290	180	145	120		18	3		4-φ18	232	690
	80	310	195	160	135		20	3		8-φ18	232	715
	100	350	215	180	155		20	3		8-φ18	232	770
	125	400	254	210	185		22	3		8-φ18	283	780
	150	480	280	240	210		24	3		8-φ23	283	810
	200	600	335	295	265		26	3		12-φ23	283	967
	250	622	405	355	320		30	3		12-φ25	283	1143
	300	698	460	410	375		30	4		12-φ25	283	1292
2.5	50	230	160	125	100		20	3		4-φ18	185	645
	65	290	180	145	120		22	3		8-φ18	232	690
	80	310	195	160	135		22	3		8-φ18	232	715
	100	350	230	190	160		24	3		8-φ23	232	770
	125	400	270	220	188		28	3		8-φ25	283	780
	150	480	300	250	218		30	3		8-φ25	283	810
	200	600	360	310	278		34	3		12-φ25	283	967
	250	622	425	370	332		36	3		12-φ30	283	1143
	300	698	485	430	390		40	4		16-φ30	283	1292
4.0	50	230	160	125	100	88	20	3	4	4-φ18	185	645
	65	290	180	145	120	110	22	3	4	8-φ18	232	690
	80	310	195	160	135	121	22	3	4	8-φ18	232	715
	100	350	230	190	160	150	24	3	4.5	8-φ23	232	770
	125	400	270	220	188	176	28	3	4.5	8-φ25	283	782
	150	480	300	250	218	204	30	3	4.5	8-φ25	283	875
	200	600	375	320	282	260	38	3	4.5	12-φ30	283	1160